+971 4 262 3337
قم بالتبديل إلى Dark Mode

ثرمالتاكي V-Tubler PETG Tube 12mm OD، 10mm ID، 1000mm - 4 Pack | CL-W142-PL12TR-A

الموديل: CL-W142-PL12TR-A
كود التخزين: 24291
الإبلاغ عن معلومات غير صحيحة أو غير ملائمة عن المنتج.

الإبلاغ عن معلومات غير صحيحة أو غير ملائمة عن المنتج.



معلومات ثرمالتاكي V-Tubler PETG Tube 12mm OD، 10mm ID، 1000mm - 4 Pack | CL-W142-PL12TR-A



Caution

Thermaltake recommends the following steps to be taken after completing your water loop setup
  1. It is strongly recommended to use market proven pre-mix coolant, such as Thermaltake Coolant 1000. It offers great performance while preventing the entire cooling system – copper, brass, nickel, aluminum, and steel – from corrosion.
  2. Fill the reservoir with coolant and cycle the power on and off several times while the pump pushing the coolant into the loop.
  3. DO NOT let the pump run dry, when there is no liquid entering the pump turn off your power immediately
  4. Fill the reservoir to the top as it will prevent air from going into the pump
  5. If necessary tilt the system slightly from side to side to bleed the air out of the loop.
  6. Place some paper towels under fittings and joining points to test for leaks.
  7. Run the loop with the fill port open for about 24 hours to completely bleed the air out of the loop
  8. Before starting, flush out your system correctly to prevent any coolant or unwanted particles sticking to your tubes, radiators and other cooling components.
  9. Coolant might fade over time.
Thermaltake V-Tubler PETG Tube 12mm OD 10mm ID 1000mm 4 Pack

Thermaltake introduces the V-Tubler PETG solid tubing for custom PC water cooling configurations. Manufactured from premium PETG, the V-Tubler rigid tubing allows users to route the tubes runs exactly to their heart’s content. Designed with 12mm OD PETG tube adapter fittings, it gives users better mounting, easier fitting, and ideal flow to make your system a showcase for all to see.

Tt LCS Certified

Tt LCS Certified is a Thermaltake exclusive certification applied to only products that pass the design and hardcore enthusiasts standards that a true LCS chassis should be held to. The Tt LCS certification was created so that we at Thermaltake can designate to all power users which chassis have been tested to be best compatible with extreme liquid cooling configurations to ensure you get the best performance from the best features and fitment.

100% PETG Material

100% PETG Material Made in Taiwan, the V-Tubler PETG Tube is constructed from superior PETG material which is reliable, non-toxic, and substance free. Thicker walls ensure safe operation, enabling the users to make the straightest run as well as tightest bends without the need of excessive compression fittings and 90 degree angle rotaries. Working temperature ranges from -4℉ (-20℃) to 143.6℉ (62℃). 
- Outer Diameter: 12 mm 
- Inner Diameter: 10 mm 
- Length: 1000mm*4

Remarkable Expansion

Designed for use with 12mm OD PETG tube adapter fittings, V-Tubler PETG Tube is pre cut into retail coils of four 1000mm lengths, allowing enthusiasts to build up aesthetically-superior water cooling systems by allocating the radiators to each particular component and incorporating externally-modular upgrades for their chassis.

*Coolant operating temperature exceeds 50℃/122°F may potentially affect the PETG tube.
*Thermaltake V-Tubler PETG Tube Series is recommended for use with the Pacific Temperature Sensor.
قراءة المزيد

المواصفات ثرمالتاكي V-Tubler PETG Tube 12mm OD، 10mm ID، 1000mm - 4 Pack | CL-W142-PL12TR-A

جنرال لواء
العلامة التجارية
الموديل
  • CL-W142-PL12TR-A
كود تخزين مايكروليس
  • 24291
تاريخ متاح الأولى
  • 01 ديسمبر، 2018
وزن المشتريات
  • 0.60 كغ


تقييمات المستخدمين ثرمالتاكي V-Tubler PETG Tube 12mm OD، 10mm ID، 1000mm - 4 Pack | CL-W142-PL12TR-A

0
لا يوجد تقييم
كن أول من يقيم هذا المنتج

أشكركم على التصنيف!
اكتب مراجعة كاملة.
اختر الصور